The 200 cubic inch
engine was used in Mustangs from 1965 -1970. It was an inline 6 cylinder
engine with the block and valve covers painted blue.
The exhaust was a single exhaust pipe with a single inlet/outlet transverse mounted muffler
behind the axle and in front of the gas tank.
| Year |
Cylinders |
CU IN. |
HP |
Compression |
Bore x Stroke |
| 1965 |
6 |
200 |
120 |
9.2/1 |
3.680 x 3.126 |
| 1966 |
6 |
200 |
120 |
9.2/1 |
3.680 x 3.126 |
| 1967 |
6 |
200 |
120 |
9.2/1 |
3.680 x 3.130 |
| 1968 |
6 |
200 |
115 |
8.8/1 |
3.680 x 3.130 |
| 1969 |
6 |
200 |
120 |
8.1/1 |
3.680 x 3.130 |
| 1970 |
6 |
200 |
120 |
8.7/1 |
3.680 x 3.130 |
| 200 CID ENGINE SPECIFICATIONS |
| |
Motorcraft |
Delco |
Fram |
| Spark Plugs |
|
|
|
| Oil filter |
|
|
|
| Gas Filter |
|
|
|
| Air Filter |
|
|
|
| PCV |
|
|
|
| Oil |
4.5 quarts of 10W30 or 10W40 |
| Oil Pressure |
35 - 55 PSI |
| Points |
Gap and Dwell at xxx RPM |
| Timing |
6 Degrees BTDC Manual & 12 Degrees BTDC
Automatic |
| Valve adjustment |
Cold |
Hot |
| Valve size |
|
|
| Valve arrangement |
E I I E I E E I E I I E Front to rear |
| Manifold Vacuum |
17 inches at idle |
| Warm Idle Manual Trans |
575-600 RPM |
| Warm Idle Auto Trans |
500-525 RPM |
| Carburetor CFM |
|
| Bore and stroke |
3.680 X 3.126 |
| Compression |
9.2:1 (155 - 195 psi @ cranking speed) |
| Combustion chamber |
49.3 - 50.3 cc |
| HP and Torque |
120 hp at 4400 RPM and
190 ft/lbs torque at 2400 RPM |
| Taxable HP |
32.5 |
| Distributor Rotation |
Counter-Clockwise |
| Firing order |
1 - 5 - 3 - 6 - 2 - 4 |
| |
|
|
|
| |
|
|
|
| |
|
|
|
| |
|
|
|
| |
|
|
|
| |
|
|
|
| ENGINE TORQUE SPECIFICATIONS |
| All torque specifications provided in this table are
those recommended by FORD. If you use special bolts, follow the torque
specifications provided by the manufacturer. I recommend that you use
the 3 step torque technique where you torque down the bolts in three
equal steps. Once you have reached the maximum recommended torque
setting, go around one more time. Do not torque in a circular pattern.
Always torque cross to cross. |
| Head bolts |
70-75 |
Oil pan bolts |
|
| Crank cap bolts |
60-70 |
Valve cover bolts |
|
| Rod end caps |
19-24 |
Carburetor mount bolts |
|
| Intake bolts |
none |
Oil pickup |
|
| Exhaust manifold bolts |
13-18 |
Spark plugs |
|
| Harmonic damper |
85-100 |
Trans. inspection plate |
|
| A/C Compressor mounts |
|
Water pump bolts |
|
| Engine fan |
|
|
|
| Motor mounts to engine |
|
|
|
| Bellhousing bolts |
|
|
|
| Trans to bellhousing |
|
|
|
| Flywheel to Crankshaft |
75-85 |
|
|
| Crankshaft Bearing Journal Specifications
|
| Main Bearing Journal (inches) |
Connecting rod Journals |
| Journal Diameter |
Oil Clearance |
Shaft end play |
Thrust on number |
Journal Diameter |
Oil Clearance |
Side clearance |
| 2.2482 - 2.2490 |
0.0005- 0.0022 |
0.004- 0.008 |
5 |
2.1232- 2.1240 |
0.008- 0.0024 |
0.003- 0.010 |
| Piston Ring Specifications |
| Comp Ring Width |
Ring side clearance |
Ring gap width |
| Top |
Bottom |
Top |
Bottom |
Oil ring |
Top |
Bottom |
Oil Ring |
| 0.0774- 0.0781 |
0.0770- 0.0780 |
0.0019- 0.0036 |
0.0020- 0.0040 |
Snug |
0.010- 0.020 |
0.010- 0.020 |
0.015- 0.055 |
| Piston Specifications |
| Code Red |
Code Blue |
0.003 Oversize |
Piston to Cyl. Bore clearance |
Piston Pin Bore Dia. |
| 3.6778- 3.6784 |
3.6790- 3.6796 |
3.6802- 3.6808 |
0.0014- 0.0020 |
0.9122-0.9125 |
| Valve Specifications |
| Year |
Seat angle |
Face angle |
Valve spring pressure lbs/inches |
Valve spring installed height (in) |
Stem guide clearance (in) |
Stem Diameter (in) |
| Intake |
Exhaust |
Intake |
Exhaust |
| 1965 |
45 |
44 |
142-158 @ 1.222 |
1 9/16 - 1 39/64 |
0.0008- 0.0025 |
0.0018- 0.0035 |
0.3100- 0.3107 |
0.3090- 0.3097 |
| 1966 |
45 |
44 |
150@1.22 |
1 19/32 |
0.0008- 0.0025 |
0.0010- 0.0027 |
0.314 |
0.3102 |
| 1967 |
45 |
44 |
150@1.22 |
1 19/32 |
0.0008- 0.0025 |
0.0010- 0.0027 |
0.314 |
0.3102 |
| 1968 |
45 |
44 |
150@1.22 |
1 19/32 |
0.0008- 0.0025 |
0.0010- 0.0027 |
0.314 |
0.3102 |
| 1969 |
45 |
44 |
150@1.22 |
1 19/32 |
0.0008- 0.0025 |
0.0010- 0.0027 |
0.314 |
0.3102 |
| 1970 |
45 |
44 |
150@1.22 |
1 19/32 |
0.0008- 0.0025 |
0.0010- 0.0027 |
0.314 |
0.3102 |
